Charge-clustering induced fast ion conduction in 2LiX-GaF3: A strategy for electrolyte design.

2LiX-GaF3 (X = Cl, Br, I) electrolytes offer favorable features for solid-state batteries: mechanical pliability and high conductivities. However, understanding the origin of fast ion transport in 2LiX-GaF3 has been challenging. The ionic conductivity order of 2LiCl-GaF3 (3.20 mS/cm) > 2LiBr-GaF3 (0.84 mS/cm) > 2LiI-GaF3 (0.03 mS/cm) contradicts binary LiCl (10-12 S/cm) < LiBr (10-10 S/cm) < LiI (10-7 S/cm). Using multinuclear 7Li, 71Ga, 19F solid-state nuclear magnetic resonance and density functional theory simulations, we found that Ga(F,X)n polyanions boost Li+-ion transport by weakening Li+-X- interactions via charge clustering. In 2LiBr-GaF3 and 2LiI-GaF3, Ga-X coordination is reduced with decreased F participation, compared to 2LiCl-GaF3. These insights will inform electrolyte design based on charge clustering, applicable to various ion conductors. This strategy could prove effective for producing highly conductive multivalent cation conductors such as Ca2+ and Mg2+, as charge clustering of carboxylates in proteins is found to decrease their binding to Ca2+ and Mg2+.

Surface engineering of inorganic solid-state electrolytes via interlayers strategy for developing long-cycling quasi-all-solid-state lithium batteries.

Lithium metal batteries (LMBs) with inorganic solid-state electrolytes are considered promising secondary battery systems because of their higher energy content than their Li-ion counterpart. However, the LMB performance remains unsatisfactory for commercialization, primarily owing to the inability of the inorganic solid-state electrolytes to hinder lithium dendrite propagation. Here, using an Ag-coated Li6.4La3Zr1.7Ta0.3O12 (LLZTO) inorganic solid electrolyte in combination with a silver-carbon interlayer, we demonstrate the production of stable interfacially engineered lab-scale LMBs. Via experimental measurements and computational modelling, we prove that the interlayers strategy effectively regulates lithium stripping/plating and prevents dendrite penetration in the solid-state electrolyte pellet. By coupling the surface-engineered LLZTO with a lithium metal negative electrode, a high-voltage positive electrode with an ionic liquid-based liquid electrolyte solution in pouch cell configuration, we report 800 cycles at 1.6 mA/cm2 and 25 °C without applying external pressure. This cell enables an initial discharge capacity of about 3 mAh/cm2 and a discharge capacity retention of about 85%.

Lithium superionic conductors with corner-sharing frameworks.

Superionic lithium conductivity has only been discovered in a few classes of materials, mostly found in thiophosphates and rarely in oxides. Herein, we reveal that corner-sharing connectivity of the oxide crystal structure framework promotes superionic conductivity, which we rationalize from the distorted lithium environment and reduced interaction between lithium and non-lithium cations. By performing a high-throughput search for materials with this feature, we discover ten new oxide frameworks predicted to exhibit superionic conductivity-from which we experimentally demonstrate LiGa(SeO3)2 with a bulk ionic conductivity of 0.11 mS cm-1 and an activation energy of 0.17 eV. Our findings provide insight into the factors that govern fast lithium mobility in oxide materials and will accelerate the development of new oxide electrolytes for all-solid-state batteries.

High-energy and durable lithium metal batteries using garnet-type solid electrolytes with tailored lithium-metal compatibility.

Lithium metal batteries using solid electrolytes are considered to be the next-generation lithium batteries due to their enhanced energy density and safety. However, interfacial instabilities between Li-metal and solid electrolytes limit their implementation in practical batteries. Herein, Li-metal batteries using tailored garnet-type Li7-xLa3-aZr2-bO12 (LLZO) solid electrolytes is reported, which shows remarkable stability and energy density, meeting the lifespan requirements of commercial applications. We demonstrate that the compatibility between LLZO and lithium metal is crucial for long-term stability, which is accomplished by bulk dopant regulating and dopant-specific interfacial treatment using protonation/etching. An all-solid-state with 5 mAh cm-2 cathode delivers a cumulative capacity of over 4000 mAh cm-2 at 3 mA cm-2, which to the best of our knowledge, is the highest cycling parameter reported for Li-metal batteries with LLZOs. These findings are expected to promote the development of solid-state Li-metal batteries by highlighting the efficacy of the coupled bulk and interface doping of solid electrolytes.

A safe and sustainable bacterial cellulose nanofiber separator for lithium rechargeable batteries.

Bacterial cellulose nanofiber (BCNF) with high thermal stability produced by an ecofriendly process has emerged as a promising solution to realize safe and sustainable materials in the large-scale battery. However, an understanding of the actual thermal behavior of the BCNF in the full-cell battery has been lacking, and the yield is still limited for commercialization. Here, we report the entire process of BCNF production and battery manufacture. We systematically constructed a strain with the highest yield (31.5%) by increasing metabolic flux and improved safety by introducing a Lewis base to overcome thermochemical degradation in the battery. This report will open ways of exploiting the BCNF as a "single-layer" separator, a good alternative to the existing chemical-derived one, and thus can greatly contribute to solving the environmental and safety issues.

Cycling Stability of a VOx Nanotube Cathode in Mixture of Ethyl Acetate and Tetramethylsilane-Based Electrolytes for Rechargeable Mg-Ion Batteries.

The electrochemical cycling performance of vanadium oxide nanotubes (VOx-NTs) for Mg-ion insertion/extraction was investigated in acetonitrile (AN) and tetramethylsilane (TMS)-ethyl acetate (EA) electrolytes with Mg(ClO4)2 salt. When cycled in TMS-EA solution, the VOx-NT exhibited a higher capacity retention than when cycled in AN solution. The significant degradation of capacity in AN solution resulted from increased charge-transfer resistance caused by the reaction products of the electrolyte during cycling. Mixed TMS-EA solvent systems can increase the cell performance and stability of Mg-electrolytes owing to the higher stability of TMS toward oxidation and the strong Mg-coordination ability of EA. These results indicate that the interfacial stability of the electrolyte during the charging process plays a crucial role in determining the capacity retention of VOx-NT for Mg insertion/extraction.

Effects of Ni doping on the initial electrochemical performance of vanadium oxide nanotubes for Na-ion batteries.

In this study, we demonstrated the intercalation of Na in hydrothermally synthesized VOx nanotubes (NTs) and Ni-doped VOx NTs. The changes induced in the structures of the two nanomaterials during the Na intercalation process were investigated through X-ray diffraction (XRD) analyses. It was observed that the initial capacity and rate performance of the Ni-doped VOx NTs were improved. The results of X-ray photoelectron spectroscopy (XPS) and conductance measurement confirmed that higher initial capacity and rate performance were attributed to an increase in the valence states of vanadium and increased conductivity after the Ni exchange process.

Aluminum manganese oxides with mixed crystal structure: high-energy-density cathodes for rechargeable sodium batteries.

We report a new discovery for enhancing the energy density of manganese oxide (Nax MnO2 ) cathode materials for sodium rechargeable batteries by incorporation of aluminum. The Al incorporation results in NaAl(0.1) Mn(0.9) O2 with a mixture of tunnel and layered crystal structures. NaAl(0.1) Mn(0.9) O2 shows a much higher initial discharge capacity and superior cycling performance compared to pristine Na(0.65) MnO2 . We ascribe this enhancement in performance to the formation of a new orthorhombic layered NaMnO2 phase merged with a small amount of tunnel Na(0.44) MnO2 phase in NaAl(0.1) Mn(0.9) O2 , and to improvements in the surface stability of the NaAl(0.1) Mn(0.9) O2 particles caused by the formation of Al-O bonds on their surfaces. Our findings regarding the phase transformation and structure stabilization induced by incorporation of aluminum, closely related to the structural analogy between orthorhombic Na(0.44) MnO2 and NaAl(0.1) Mn(0.9) O2 , suggest a strategy for achieving sodium rechargeable batteries with high energy density and stability.